PassLeader just published the NEWEST Fortinet FCP_FAZ_AD-7.4 exam dumps! And, PassLeader offer two types of the FCP_FAZ_AD-7.4 dumps — FCP_FAZ_AD-7.4 VCE dumps and FCP_FAZ_AD-7.4 PDF dumps, both VCE and PDF contain the NEWEST FCP_FAZ_AD-7.4 exam questions, they will help you PASSING the Fortinet FCP_FAZ_AD-7.4 exam easily! Now, get the NEWEST FCP_FAZ_AD-7.4 dumps in VCE and PDF from PassLeader — https://www.passleader.com/fcp-faz-ad-7-4.html (111 Q&As Dumps –> 178 Q&As Dumps)
What’s more, part of that PassLeader FCP_FAZ_AD-7.4 dumps now are free — https://drive.google.com/drive/folders/1Mcadk3PGULKtsjV7mpWbm90Zc–o7ksD
NEW QUESTION 81
If a hard disk fails on a FortiAnalyzer that supports software RAID, what should you do to bring the FortiAnalyzer back to functioning normally, without losing data?
A. Hot swap the disk.
B. Replace the disk and rebuild the RAID manually.
C. Take no action if the RAID level supports a failed disk.
D. Shut down FortiAnalyzer and replace the disk.
Answer: D
Explanation:
If a hard disk on a FortiAnalyzer unit fails, it must be replaced. On FortiAnalyzer devices that support hardware RAID, the hard disk can be replaced while the unit is still running-known as hot swapping. On FortiAnalyzer units with software RAID, the device must be shutdown prior to exchanging the hard disk.
NEW QUESTION 82
When generating reports on FortiAnalyzer, macros can be used to include additional data. Which two statements about macros are true? (Choose two.)
A. Macros are abbreviated dataset queries.
B. Macros do not need to be associated with a chart.
C. Macros are supported in FortiGate ADOMs only.
D. Macros cannot be customized.
Answer: AB
NEW QUESTION 83
Logs are being deleted from one of your ADOMs earlier that the configured setting for archiving in your data policy. What is the most likely problem?
A. The total disk space is insufficient and you need to add other disk.
B. CPU resources are too high.
C. The ADOM disk quota is set too low based on log rates.
D. Logs in that ADOM are being forwarded in real-time to another FortiAnalyzer device.
Answer: C
NEW QUESTION 84
What remote authentication servers can you configure to validate your FortiAnalyzer administrator logons? (Choose three.)
A. RADIUS
B. Local
C. LDAP
D. PKI
E. TACACS+
Answer: ACE
NEW QUESTION 85
What are the operating modes of FortiAnalyzer? (Choose two.)
A. Standalone
B. Manager
C. Analyzer
D. Collector
Answer: CD
NEW QUESTION 86
Which clause is considered mandatory in SELECT statements used by the FortiAnalyzer to generate reports?
A. FROM
B. LIMIT
C. WHERE
D. ORDER BY
Answer: A
Explanation:
https://kb.fortinet.com/kb/documentLink.do?externalID=FD48500
NEW QUESTION 87
Which two statements express the advantages of grouping similar reports? (Choose two.)
A. Improve report completion time.
B. Conserve disk space on FortiAnalyzer by grouping multiple similar reports.
C. Reduce the number of hcache tables and improve auto-hcache completion time.
D. Provides a better summary of reports.
Answer: AC
NEW QUESTION 88
Which two statement are true regardless initial Logs sync and Log Data Sync for Ha on FortiAnalyzer?
A. By default, Log Data Sync is disabled on all backup devise.
B. Log Data Sync provides real-time log synchronization to all backup devices.
C. With initial Logs Sync, when you add a unit to an HA cluster, the primary device synchronizes its logs with the backup device.
D. When Logs Data Sync is turned on, the backup device will reboot and then rebuilt the log database with the synchronized logs.
Answer: CD
NEW QUESTION 89
Which two statements about a FortiAnalyzer Fabric are true? (Choose two.)
A. Fabric members must be in the same time zone as the supervisor.
B. Fabric members and the supervisor support HA.
C. All fabric members must run in collector mode except the supervisor.
D. The supervisor can access the logs in the fabric members using an API.
Answer: AD
Explanation:
All FortiAnalyzer Fabric members must be configured with the same time zone settings as the supervisor. The Supervisor can view the information on the members via an API.
NEW QUESTION 90
What is the purpose of output variables?
A. To store playbook execution statistics.
B. To use the output of the previous task as the input of the current task.
C. To display details of the connectors used by a playbook.
D. To save all the task settings when a playbook is exported.
Answer: B
Explanation:
Output variables allow you to use the output from a preceding task as an input to the current task.
NEW QUESTION 91
Which two statements are correct regarding the export and import of playbooks? (Choose two.)
A. You can export only one playbook at a time.
B. You can import a playbook even if there is another one with the same name in the destination.
C. Playbooks can be exported and imported only within the same FortiAnaryzer.
D. A playbook that was disabled when it was exported, will be disabled when it is imported.
Answer: BD
Explanation:
– Option B: If the imported playbook has the same name as an existing one, FortiAnalyzer will create a new name that includes a timestamp to avoid conflicts.
– Option D: Playbooks are imported with the same status they had (enabled or disabled) when they were exported. Playbooks set to run automatically should be exported while they are disabled to avoid unintended runs on the destination.
NEW QUESTION 92
You are looking for a playbook that was exported by a junior administrator. You perform a search and find the files listed below. Which file will perform an import operation?
A. Exported_playbook.json
B. Exported_playbook.csv
C. Exported_playbook.txt
D. Exported_playbook.sql
Answer: A
Explanation:
https://docs.fortinet.com/document/fortianalyzer/7.4.0/administration-guide/949810/importing-and-exporting-playbooks
NEW QUESTION 93
What is required to authorize a FortiGate on FortiAnalyzer using Fabric authorization?
A. A FortiGate ADOM.
B. The FortiGate serial number.
C. A pre-shared key.
D. Valid FortiAnalyzer credentials.
Answer: D
Explanation:
This method requires that both FortiGate and FortiAnalyzer are running version 7.0.1 or higher. It is also required that the FortiGate administrator has valid credentials to log in on FortiAnalyzer and complete the registration.
NEW QUESTION 94
If the primary FortiAnalyzer in an HA cluster fails, how is the new primary elected?
A. The configured IP address is checked first.
B. The active port number is checked first.
C. The firmware version is checked first.
D. The configured priority is checked first.
Answer: D
Explanation:
In the case of a primary device failure, FortiAnalyzer HA uses the following rules to select a new primary:
– All cluster devices are assigned a priority from 80 to 120. The default priority is 100. If the primary device becomes unavailable, the device with the highest priority is selected as the new primary device. For example, a device with a priority of 110 is selected over a device with a priority of 100.
– If multiple devices have the same priority, the device whose primary IP address has the greatest value is selected as the new primary device. For example, 123.45.67.124 is selected over 123.45.67.123.
– If a new device with a higher priority or a greater value IP address joins the cluster, the new device does not replace (or pre-empt) the current primary device automatically.
NEW QUESTION 95
Which statement correctly describes the management extensions available on FortiAnalyzer?
A. Management extensions do not require additional licenses.
B. Management extensions allow FortiAnalyzer to act as a ForbSIEM supervisor.
C. Management extensions require a dedicated VM for best performance.
D. Management extensions may require a minimum number of CPU cores to run.
Answer: D
Explanation:
Review the hardware requirements before you enable a management extension application. Some of them require a minimum amount of memory or a minimum number of CPU cores.
NEW QUESTION 96
When working with FortiAnalyzer reports, what is the purpose of a dataset?
A. To provide the layout used for reports.
B. To define the chart type to be used.
C. To retrieve data from the database.
D. To set the data included in templates.
Answer: C
Explanation:
Another common way to load data into a DataSet is to use the DataAdapter class to retrieve data from the database.
NEW QUESTION 97
You crested a playbook on FortiAnalyzer that uses a FortiOS connector. When configuring the FortiGate side, which type of trigger must be used so that the actions in an automation stitch are available in the FortiOS connector?
A. FortiAnalyzer Event Handler.
B. Incoming webhook.
C. FortiOS Event Log.
D. Fabric Connector event.
Answer: B
Explanation:
In order to see the actions related to the FOS connector, you must enable an automation rule using the Incoming Webhook Call trigger on the FortiGate side.
NEW QUESTION 98
What must you consider when using log fetching? (Choose two.)
A. The fetch client can retrieve logs from devices that are not added to its local Device Manager.
B. You can use filters to include only logs from a single device.
C. The fetching profile must include a user with the Super_User profile.
D. The archive logs retrieved from the server become archive logs in the client.
Answer: AB
Explanation:
– Option A: This is because the fetch client uses the FortiAnalyzer API to retrieve logs, and the API does not require the devices to be added to the local Device Manager.
– Option B: This can be useful if you only want to fetch logs from a specific device, or if you want to exclude logs from certain devices.
NEW QUESTION 99
Which two statements are true regarding the outbreak detection service? (Choose two.)
A. New alerts are received by email.
B. Outbreak alerts are available on the root ADOM only.
C. An additional license is required.
D. It automatically downloads new event handlers and reports.
Answer: CD
Explanation:
– Option C: An additional license is required. The Outbreak Detection Service is a licensed feature that must be purchased separately.
– Option D: It automatically downloads new event handlers and reports. When a new outbreak is detected, the Outbreak Detection Service will automatically download the associated event handlers and reports to the FortiAnalyzer.
NEW QUESTION 100
Why must you wait for several minutes before you run a playbook that you just created?
A. FortiAnalyzer needs that time to parse the new playbook.
B. FortiAnalyzer needs that time to back up the current playbooks.
C. FortiAnalyzer needs that time to ensure there are no other playbooks running.
D. FortiAnalyzer needs that time to debug the new playbook.
Answer: A
Explanation:
When you create a new playbook, FortiAnalyzer needs to parse the playbook file to understand the commands and tasks that it contains. This can take a few minutes, depending on the size and complexity of the playbook.
NEW QUESTION 101
How can you attach a report to an incident?
A. By attaching it to an event handler alert.
B. By editing the settings of the desired report.
C. From the properties of an existing incident.
D. Saving it in JSON format, and then importing it.
Answer: C
Explanation:
To do this, follow these steps:
1. Go to Incidents & Events –> Incidents.
2. Select the incident that you want to attach the report to.
3. Click the Properties tab.
4. In the Reports section, click Add.
5. Select the report that you want to attach.
6. Click OK.
The report will be attached to the incident.
NEW QUESTION 102
……
Learning the PassLeader FCP_FAZ_AD-7.4 dumps with VCE and PDF for 100% passing Fortinet certification — https://www.passleader.com/fcp-faz-ad-7-4.html (111 Q&As Dumps –> 178 Q&As Dumps)
BONUS!!! Download part of PassLeader FCP_FAZ_AD-7.4 dumps for free — https://drive.google.com/drive/folders/1Mcadk3PGULKtsjV7mpWbm90Zc–o7ksD